467575 Replacement Vita Spa Pack 220 Volts

Replacement Spa Pack for Vita Spas

All Spa Packs are configured to meet your spa needs. The spa packs are made to order (this means you are buying a brand new spa pack, not a pack that has been on a shelf for 2 years) and sometimes will require a 2 to 3 day lead time.

The beauty of the C5 control series is its simplicity. All the components from the relays to the fuses are located right on the board. This is nothing new, except that the C5 series accomplishes this without having high voltage run through the board. With this unique design, you get the convenience of an all-in-one board with the safety and longevity of low power electronics.

The C5 goes a step further. The C5 also incorporates color coded receptacles and wiring so changing the voltage of a component is as easy as moving its color coded neutral wire on the power block.

Standard Features that come with this spa pack are:
- Self-Standing Control
- T7 Digital Topside

- Topside Adapter/ Extension Face Plate
- A cord for 2 Speed 1st Pump Ready w/Cord
- 1 Speed 2nd Pump Ready
- Circulation Pump Ready
- Blower Ready
- A cord for 12v Spa Light Ready w/Cord
- Ozone Ready
Flo-Thru Stainless Steel Heater:  Note if you have a low flow vertical heater on your spa, you can not use this spa pack.

- 11" Tall
- 19" Wide
- 3.25" Deep

- T7 Topside Dimensions: 5" x 2.5"

- Adapter Face Plate Dimensions:  8-1/4" x 3-3/8"
- The included T7 Topside requires only a 1.75" hole saw to install!

NOTE: These units come standard with 2 cords. A cord for the light and a cord for a two speed primary pump, if additional AMP cords are needed please check out the 'Cords and Receptacles' section of the store. If you order them above with the spa control you will save a couple of dollars.

We have replaced a lot of old Vita Spa Packs like the one that you have. The new packs come complete with the Box, circuit board, heater, sensors and digital spa side controller (see all the features listed above). The pack does not include a new complete motor or air blower. If you decide to replace this pack and you need a new complete motor or air blower, we will discount them to help make the whole repack job more affordable and justified.


This replacement spa pack comes from the Factory already pre-wired. The standard primary and secondary pumps (not included with this spa pack) are wired for 240 volts. The light is wired for 12 volts, and all other components: blower, ozone, circulation pump, and stereo/aux, also not included with spa pack) are all wired for 120 volts. This is not an issue for your spa because all the voltages of these controls may easily be changed by moving the neutral wires at the power block in the control as needed. Also, if you are using a second pump make sure to choose the voltage.


NOTE: If you have a 3 Wire 220 Volts power supply coming into the spa pack, all components (motors, blower and ozonator) must be 220 volts. If your motor or air blower are 110 volts then you will need to bring a neutral wire to the spa pack (known as a 4 wire system) or replace them with a 220 volt motor or blower.


We have include the Topside Extension Plate if you are replacing a larger topside then the T7.  Be sure to order a 1/4" Thermo-well/Bushing (dry sensor well/housing) if the spa you are installing the control into doesn't already have one installed. You can order at the bottom of this page under related products or in the spa parts category

Safety, built-in

The C5 series of controls are one of the industry’s first controls to be fully tested and approved under the latest editions of UL testing requirements for the United States, and CSA testing requirements for Canada

The T7 Topside control comes standard with every C5 control system sold, and can be programmed for almost any spa's configuration. From a spa with a single pump and light, to a spa with a circulation pump, two booster pumps, air blower, ozonator, fiber optic lighting, and an entertainment system.

Programming the T7 topside is simple and all done using the keypad. The T7 doesn't need a battery to remember its settings. On-board flash memory makes sure that once a topside is programmed, it stays that way regardless of power status.


If you have a low flow heater that looks like this 411102 - Vertical Heater Assembly 220V then you can not use this spa pack. You would need a special "Low Flow Spa Pack".

If you have any questions or concerns about this spa pack please contact our sales department at 386-677-2120.

467575 Replacement Vita Spa Pack 220 Volts
Click To Enlarge
  • Item #: 467575
  * Marked fields are required.
Price $545.95